產品中心
products

靖江市鑫昊環?萍加邢薰
手機:18360017001
電話:0523-84936533
傳真:0523-84936533
地址:靖江市新港園區創新村
網址:www.obbip.com
焚燒爐燃燒器常見故障分析
[ 時間:2017/4/26 17:06:45 點擊: ]
1、燃燒器不能啟動了,是何道理?
a、爐內光線強烈及其它地方有光透入到燃燒器光敏管,應及時排除泄漏。
b、無電源輸入。
c、程控器損壞。
d、油路堵塞
2、燃燒器,點火失靈應該怎么辦?
a、第一次或油位低時點火,油管含空氣首次點火可能不成功,需在點火不成功后20秒按復位鍵重新啟動燃燒器,有時可能以上動作要進行幾次。
b、燃料過濾器堵塞,應及時清洗過濾器。
c、油壓不合理,霧化不好,調整出口壓力至10-12Kgf/cm2。
d、電磁閥失靈了,檢修或更換。
e、點火電極距離太遠,重新調整至3-5mm。
f、 點火變壓器故障,及時更換。
4、燃燒器故障表格分析
故障現象 Fault phenomenon | 可能的原因 Possible reason | 解決辦法 Solution |
燃燒器不啟動 Burner does not start | 無電源 no power supply | 檢查電源 L-N線之間的電壓220V是否存在 Check the power supply voltage between LN Line the existence of 220V |
檢查保險絲的情況 Check the fuses | ||
復位鈕紅燈亮 燃燒器鎖定 Reset button the red light Burner lock | 重新按復位按鈕 Re-press the reset button | |
光電管感受到光線 Phototube feel light | 消除光源 The elimination of the light source | |
控制盒的接線錯誤 Control box wiring error | 檢查并重接 Inspection and re-wiring | |
在預吹掃及點火周期,燃燒器運行正常,但5秒后鎖定 In the pre-purge and ignition cycle, the burner is running normal, but five seconds later the lock | 光電管臟 光電管壞 Phototube dirty Phototube bad | 清洗 更換 Cleaning Replacement |
脫火或熄火 From fire or flameout | 檢查泵壓力及燃料的輸出 Check the pump pressure and fuel output | |
檢查風量 Check the air flow | ||
更換噴嘴 Replacement nozzle | ||
檢查電磁閥線圈 Check the solenoid valve coil | ||
燃燒器啟動并有點火延遲 Burner start and ignition delay | 點火電極位置不對 Ignition electrode wrong location | 按手冊的說明進行調節 According to the instructions manual adjustment |
噴嘴臟或損壞 Nozzle dirty or damaged | 更換 change | |
燃燒器啟動運行一段時間后熄火 Burner start running some time and then flameout | 油路閥門未開 油路過濾器堵塞 油箱缺油 Oil valve is not open Oil filter plug Oil tank oil less | 打開閥門 清洗過濾器 油箱加滿油 Open valve Cleaning filter Top up oil |
燃燒器點火后火焰不穩定 After the ignition burner flame instability | 點火電極位置 Ignition electrode position | 按手冊的說明進行調節 According to the instructions manual adjustment |
油泵壓力低 Oil pump low pressure | 一般出廠設置為12bar General set to 12bar |
下一篇:垃圾焚燒爐的工作原理